Sikafloor®-161
Epoxy Primer , Levelling Sealer , Intermediate Layer and Mortar Screed
Sikafloor®-161 is a high grade , high build multipurpose epoxy resin which can be used as surface sealer or scratch coat with and without the addition of the suitable quartz sand or filler .
- Good penetration
- Good bond strength
- Economical and easily applied
- Short waiting times
- Multi-purpose use
Usage
- Priming concrete substrates, cement screeds and epoxy mortars
- For low to medium absorbent substrates
- Epoxy primer under different bases of flooring systems such as resin epoxy base , fully polyurethane systems and polyurethane screeds
- Intermediate layer underneath multi products such Floor 92EG , Floor 92SL , Floor 264 , Floor 263SL , Floor 359EG , Purcem , Gard rang
- May be mixed with sand to the desired consistency to repair patches or form covings
- Binder for levelling layers and mortar screeds
- Used as well as for the filling of fissures and joints
Advantages
- Good penetration
- Good bond strength
- Economical and easily applied
- Short waiting times
- Multi-purpose use
Colour
Part A | brownish-transparent, liquid |
Part B | transparent, liquid |
Product Details
SUSTAINABILITY
- Sikafloor®-161 conforms to the requirements of LEED EQ Credit 4.2: Low-Emitting Materials: Paints & Coatings SCAQMD Method 304-91 VOC Content < 100 g/l
APPROVALS / CERTIFICATES
- CE Marking and Declaration of Performance to EN 1504-2 - Surface protection product for concrete - Coating
- CE Marking and Declaration of Performance to EN 13813 - Resin screed material for internal use in buildings
- Coating Compatibility DIN EN 13578, Sikafloor®-161 / -264, Polymer Institut, Test report No. P 6239
Composition
Epoxy
Shelf life
12 months from date of production
Storage conditions
The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +30 °C. Always refer to packaging.
Solid content by weight
~100 %
Solid content by volume
~100 %
Volatile organic compound (VOC) content
< 100 g/l
Shore D Hardness
~76 (7 days / +23 °C) | (DIN 53 505) |
Abrasion Resistance
Mortar Screed when mixed with Sikadur 506 (C): 48mg loss
( CS 17 / 1000 Cycle / 1000 g )
Compressive Strength
Resin: ~ 60 N/mm2 (28 days / +23 C) ( EN 196-1)
Resin: ~ 50 N/mm2 (14 days / +23 C) ( ASTM C579 - Method B )
Mortar Screed when mixed with Sikadur 506 (C):~ 70 N/mm2 (14 days / +23 C) ( ASTM C579 - Method B )
Tensile Strength in Flexure
Resin : > 26 N/mm² (ASTM D790)
Mortar Screed when mixed with Sikadur 506 (C): >37N/mm² (ASTM D790)
Tensile Strength
Resin: ~ 60 N/mm2 (28 days / +23 C) ( ASTM D638 )
Tensile Adhesion Strength
> 1.7 N/mm² (failure in concrete) Resin > 1.6 N/mm² (failure in concrete) Mortar Screed | (ASTM D4541 - Pull off) (ISO 4624 - Pull off) |
Resistance to Impact
Excellent
Chemical Resistance
Resistant to wide rang of general chemicals and acids .
For severe conditions , please refer to Sika`s Representative
Temperature Resistance
Exposure* | Dry heat |
Permanent | +50 °C |
Short-term max. 7 days | +80 °C |
Short-term max. 12 hours | +100 °C |
Short-term moist/wet heat* up to +80 °C where exposure is only occasional (steam cleaning etc.).
*No simultaneous chemical and mechanical exposure and only in combination with Sikafloor® systems as a broadcast system with approx. 3–4 mm thickness.
Application
Ambient Air Temperature
+10 °C min. / +30 °C max.
Relative Air Humidity
80 % r.h. max.
Dew Point
Beware of condensation.
The substrate and uncured applied floor material must be at least +3 °C above dew point to reduce the risk of condensation or blooming on the floor finish. Low temperatures and high humidity conditions increase the probability of blooming.
Substrate Temperature
+10 °C min. / +30 °C max.
Substrate Moisture Content
≤ 6 % pbw moisture content using the Sika® - Tramex meter (at the time of application).
Note the moisture content must be ≤ 4 % pbw when using the CM measurement or Oven-dry-method. Test method: Sika®-Tramex meter, CM - measurement or Oven-dry-method. No rising moisture according to ASTM (Polyethylene-sheet).
Pot Life
Temperature | Time |
+10 °C | ~50 minutes |
+20 °C | ~25 minutes |
+30 °C | ~15 minutes |
Curing Time
Before applying non-solvent based products on Sikafloor®-161 allow:
Substrate temperature | Minimum | Maximum |
+10 °C | 24 hours | 4 days |
+20 °C | 12 hours | 2 days |
+30 °C | 8 hours | 24 hours |
Before applying solvent based products on Sikafloor®-161 allow:
Substrate temperature | Minimum | Maximum |
+10 °C | 36 hours | 6 days |
+20 °C | 24 hours | 4 days |
+30 °C | 16 hours | 2 days |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Consumption
Coating System | Product | Consumption |
Priming (Low Porosity Surface) | 1 x Sikafloor®-161 | 1 layer × 0.15 - 0.2 kg/m² |
Priming (Medium Porosity Surface) | 2 x Sikafloor®-161 | 2 layers × 0.15 kg/m²/layer |
Surface Sealer (High Porosity Surface) | 1 pbw Sikafloor®-161 : 1 pbw fine filler ( K4 ) | 1 layers × 0.3 - 0.35 kg/m² |
Epoxy screed / Repair Mortar (4 –12 mm layer thickness ) | 1 pbw Sikafloor®-161 : 8 -10 pbw quartz sand (Dur 506) | 2.2 kg/m²/mm |
These figures are theoretical and do not allow for any additional material required due to surface porosity, surface profile, variations in level or wastage etc.
MIXING
Prior to mixing all parts, mix separately part A (resin) using a low speed single paddle electric stirrer (300 - 400 rpm). Add part B (hardener) to part A and mix it together continuously for 2-3 minutes until a uniform mix has been achieved. When parts A and B have been mixed , gradually add the appropriate granulometry of dried quartz sand and if required Extender T.
Mix for a further 2 - 3 minutes until a uniform mix has been achieved. To ensure thorough mixing pour materials into another container and mix again to achieve a smooth consistent mix. Excessive mixing must be avoided to minimise air entrainment. During the final mixing stage, scrape down the sides and bottom of the mixing container with a flat or straight edge trowel at least once to ensure complete mixing.
For more details or clarification , please refer to Sika`s Technical Team .
APPLICATION
Strictly follow installation procedures as defined in method statements, application manuals and working instructions which must always be adjusted to the actual site conditions.
Prior to application, confirm substrate moisture content, relative air humidity, dew point, substrate, air and product temperatures. If moisture content > 6% parts by weight, Sikafloor® EpoCem® may be applied as a Temporary Moisture Barrier (T.M.B.) system.
Primer
Pour mixed Sikafloor®-161 onto the prepared substrate and apply by brush, roller or squeegee then back roller in two directions at right angles to each other. Ensure a continuous, pore free coat covers the substrate. If necessary, apply two priming coats.
Confirm primer waiting /overcoating time has been achieved before applying subsequent products.
Surface Sealer ( Scratch Layer )
Spread the mix Sikafloor®-161 with fine filler ( K4 ) using notched trowel as a scratch coat .
Epoxy screed / repair mortar
Apply the repair or screed mortar onto the “tacky” primer layer . For the screed, use levelling battens and screed rails as necessary. After a short waiting time, compact and smoothen the mortar with a trowel. For the screed, a teflon coated power float (~20 - 90 rpm) is recommended.
CLEANING OF EQUIPMENT
Clean all tools and application equipment with Thinner C immediately after use. Hardened material can only be removed mechanically.
Documents
دهان برايمر من مركبين منخفض اللزوجة أساسه راتنج الإيبوكسى .
الإستعمالات
يستعمل كبرايمر ومادة رابطة على الآتى :
الخرسانة والحجارة الطبيعية والمونة الإيبوكسية .
المونة الأسمنتية ، البياض ، أسمنت الأسبستوس .
دهان الأرضيات الإيبوكسية الذاتى التسوية ومون الإصلاح الإيبوكسية .
المميزات
تغلغل وتشرب جيد مع قوة إلتصاق عالية .
سهل الإستخدام ويمكن إستعماله فى درجات حرارة منخفضة حتى ۱۰ °م .