SikaGrout®-980

Up to 12 months shelf life when stored in recommended conditions.

Store at ambient temperatures, out of direct sunlight, in cool, dry warehouse conditions and clear of the ground on pallets protected from rainfall prior to application. No permanent storage over +30 °C.

SikaGrout®-980 grouts can withstand high temperature (+400 °C) for very long periods without substantial deterioration.

Suitable for thickness above 80 mm and with min thickness 25 mm

Note: Technically, the minimum application thickness is around 25 mm. For grouting below 25 mm thickness, Contact us for technical guidance.

+5 °C to +35 °C

+5 °C to +35 °C

Approx. 45 minutes (at 20 °C)

Wait for at least 12 hours (at +20 °C) before removing the formwork.

Approx. 2.3 kg/l

One 30 kg bag will yield approximately 15.2-15.6L depending on the water demand used.

The performance, durability and safety of the installed product used for anchoring steel (rebar), bolts and screws strongly depend on the substrate, the dimensions of the element, the drilling and cleaning of holes, the substrate temperature and the type of anchoring bolt or bar. It is therefore important that a proper structural assessment of the structural elements to be repaired is carried out by qualified engineers, and that the choice of products, anchor types etc. is based upon such assessment.

The concrete should be free of frost, curing membranes, waterproofing treatments, oil stains, laitance, friable material and dust.

The concrete surfaces should be chipped and if there is a water leakage it must be drained or properly plugged. Saturate the cleaned foundation and any bolt holes with water for at least 6 hours, preferably 24 hours.

Just before grouting, surfaces should be damp, but free of standing water. Particular attention should be paid to bolt holes to ensure that these are water-free. Use oil free compressed air to blow out bolt holes and pockets as necessary.

Base plates, bolts, etc. must be clean and free of oil, grease and paint etc. Set and align equipment. If shims are to be removed after the grout has set, then lightly grease them for easy removal.

The formwork must fit tightly against the substrate and, when grouting material around machines, it has to be at least 2 cm higher than the bottom of the plate to be underpoured. Ensure formwork is secure and watertight to prevent movement and leaking during the placing and curing of the grout.

The area should be free of excessive vibration. Shut down adjacent machinery until the grout has hardened.

In hot weather, base plates and foundations must be shaded from direct sunlight. Bags of grout should be stored in the shade prior to use.

In cold weather, the temperature of base plates and foundations should be raised to over 10°C.

We strongly recommend to use force action mixers. Only small amounts of grout can be mixed by a powerful electric drill with a suitable paddle attached to it.

Damp down the inside of the grout mixer with water prior to mixing the initial batch of SikaGrout®-980. Ensure the mixer is damp but free of standing water. Add 90% of the pre measured quantity of water. Slowly add the SikaGrout®-980 mixing continuously. Mix for two minutes until a smooth, uniform, lump free consistency is achieved, then add the remaining water and mix for a further 3 minutes.

Do not exceed the allowed maximum water amount!

Before grouting, determine if there is excess vibration of the foundation or baseplate caused by nearby operating equipment. Shut down this source of vibration until after the newly-placed grout has taken final set.

Pour mixed SikaGrout®-980 grout into the voids without interruption. The mortar flow can be improved by moving chains or wire slings in the fresh mortar when areas are inaccessible. The grout shall be poured continuously and from one side only, to avoid entrapment of air while grouting.
Make sure the mortar fills the entire space to be grouted and remains in contact with the plate throughout the entire grouting placement.

Where grout must flow some distance, make the initial batch slightly more fluid or flowable than required; this lubricates the surfaces and avoids blockage of the grout that follows.

Due to differences in temperature between the grout under the base plate, and exposed shoulders that are subject to more rapid temperature changes, debonding or cracking can occur. Avoid shoulders wherever possible. If shoulders are required, they should be firmly anchored with reinforcing to the substrate to prevent debonding.

In case of machine application: check pumping equipment for the maximum allowed grain size – SikaGrout®-980 contains aggregate up to 8 mm diameter.

Note: Do not use vibrator for placing the grout!

Immediately after SikaGrout®-980 is placed, cover all exposed grout with clean wet hessian and keep moist by covering with polythene.

Tools and mixer must be cleaned immediately after use with water. Cured material can only be removed mechanically.