Sikafloor®-359 N
Sikafloor®-359 N is a two part tough-elastic, coloured, non-yellowing, polyurethane seal coat.
- Tough-elastic.
- Good mechanical and chemical resistance
- Non-yellowing.
- Watertight.
- Good opacity.
- Matt finish.
- Easy to apply.
- Slip resistant surface possible.
Usage
- Abrasion resistant seal coat with high mechanical resistance for broadcast
- systems with crack-bridging properties in industrial flooring.
- Particularly suitable for car park decks, ramps and warehouses etc.
Advantages
- Tough-elastic.
- Good mechanical and chemical resistance
- Non-yellowing.
- Watertight.
- Good opacity.
- Matt finish.
- Easy to apply.
- Slip resistant surface possible.
Packaging
Part A | 25.35 kg containers |
Part B | 7.15 kg containers |
Part A+B | 32.5 kg ready to mix units |
Colour
Resin - part A | coloured, liquid |
Hardener - part B | transparent, liquid |
Almost unlimited choice of colour shades.
Product Details
APPROVALS / CERTIFICATES
- Certifed as part of the Surface Protection System OS 11a & 11b according to DIN EN 1504-2 and DIN V18026
- Conforms to the requirements of DIN 51130 for class R12 (Skid / slip resistance), report No. 12 4274-S/06, MPI, Germany, 2006
- Fire classification in accordance with EN 13501-1 for class B(fl)-s1, MPA Dresden, Germany, 2007 .
- Reaction to fire in accordance with DIN EN ISO 9239-1.
Composition
Polyurethane
Shelf life
12 months from date of production
Storage conditions
The packaging must be stored properly in original, unopened and undamaged sealed packaging, in dry conditions at temperatures between +5°C and +30°C.
Density
Part A | ~ 1.67 kg/l |
Part B | ~ 1.05 kg/l |
Mixed resin | ~ 1.45 kg/l |
All Density values at +23°C
Solid content
~ 85% (by volume) / ~ 85% (by weight)
VOC DATA
VOC content (ready to use) > 250 g/l (Type of regulate paint under the Air Pollution Control (Volatile Organic Compounds)
Shore Hardness
~ 52 (7Days / 23o ) | (DIN 53 505) |
Abrasion Resistance
180 mg (CS 10/1000/1000) (7 days / +23°C) | (DIN 53 109 (Taber Abrader Test) ) |
Tensile Adhesion Strength
> 1.5 N/mm2 (failure in concrete) | (ISO 4624) |
Chemical Resistance
Resistant to many chemicals. Please ask for a detailed chemical resistance table.
Temperature Resistance
Exposure* | Dry heat |
Permanent | +50°C |
Short-term max. 7d | +80°C |
Short-term max. 4h | +100°C |
*No simultaneous chemical and mechanical exposure.
Short-term moist/wet heat* up to +80°C where exposure is only occasional (high pressure water jetting etc.)
Application
Ambient Air Temperature
+10°C min. / +30°C max.
Relative Air Humidity
80% r.h. max.
Dew Point
Beware of condensation!
The substrate and uncured floor must be at least 3°C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate Temperature
+10°C min. / +30°C max.
Substrate Moisture Content
< 4% pbw moisture content.
Test method: Sika®-Tramex meter, CM - measurement or Oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet).
Pot Life
Temperatures | Time |
+10°C | ~ 40 minutes |
+20°C | ~ 25 minutes |
+30°C | ~ 15 minutes |
Curing Time
Before applying Sikafloor®-359 N on Sikafloor®-375/ -350 N/ -326/ -261 broadcast allow:
Substrate temperature | Minimum | Maximum |
+10°C | 24 hours | * |
+20°C | 12 hours | * |
+30°C | 6 hours | * |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Applied Product Ready for Use
Temperature | Foot traffic | Light traffic | Full cure |
+10°C | ~ 48 hours | ~ 5 days | ~ 10 days |
+20°C | ~ 24 hours | ~ 3 days | ~ 7 days |
+30°C | ~ 16 hours | ~ 2 days | ~ 3 days |
Note: Times are approximate and will be affected by changing ambient conditions
Consumption
Coating System | Product | Consumption |
Seal coat for EP / PUR broadcast systems
Quartz sand 0.3 - 0.8 mm Quartz sand 0.7 - 1.2 mm | Sikafloor®-359 N |
~ 0.7 - 0.9 kg/m² |
Car park decking systems (according to the German Standard DAfStb Rili-SIB
2001):
Classification OS 11a
Coating System | Product | Consumption |
Primer (lightly blinded) | Sikafloor®-156 / -161 Quartz sand 0.3 - 0.8 mm | 0.3 - 0.5 kg/m2 ~ 0.8 kg/m2 |
Base coat | Sikafloor®-350 N Elastic | ~ 2.0 kg/m2 |
Wearing course | Sikafloor®-355 N filled Broadcast in excess with Quartz sand 0.3 - 0.8 mm or 0.7 - 1.2 mm | ~ 1.86 kg/m2 (1.55 kg/m2 binder + 0.31 kg/m2 quartz sand 0.1-0.3mm) 6 - 8 kg/m2 |
Seal coat | Sikafloor®-359 N | 0.7 - 0.9 kg/m2 |
Classification OS 11b
Coating System | Product | Consumption |
Primer (lightly blinded) | Sikafloor®-156 / -161 Quartz sand 0.3 - 0.8 mm | 0.3 - 0.5 kg/m2 ~ 0.7 kg/m2 |
Wearing course | Sikafloor®-350 N filled Broadcast in excess with Quartz sand 0.3 - 0.8 mm or 0.7 - 1.2 mm | ~ 2.4 kg/m2 (2.0 kg/m2 binder + 0.4 kg/m2 quartz sand 0.1-0.3 mm)
6 - 8 kg/m2 |
Seal coat | Sikafloor®-359 N | 0.7 - 0.9 kg/m2 |
These figures are theoretical and do not allow for any additional material due to
application technique, surface porosity, surface profile, variations in level and
wastage etc.MIXING
Part A : part B = 78 : 22 (by weight)
APPLICATION
Prior to application, confirm substrate moisture content, r.h. and dew point.
Seal coat:
Sealer coats can be applied by squeegee and then back-rolled (crosswise) with a
short-piled roller.
CLEANING OF EQUIPMENT
Clean all tools and equipment immediately after use with Colma-Cleaner. Once hardened, the material can only be removed mechanically. Wash soiled hands and skin thoroughly with hot soapy water.